Beli jual ball plunger di monotaro.id

The large lead rolled ball screw is provided on the end face of the ball screw nut after rolling motion of the ball rolling surface provided on the screw shaft and ball screw nut with the load ball around the screw shaft while receiving the axial load It is scooped up from the groove with the end cap, circulates through the ball screw nut and reaches the load zone again from the opposite end cap to make infinite rolling motion. The ball rolling surface of the screw shaft is rolled to the right thread, and the ball rolls in the groove. Stable operation is obtained even at high speed rotation, so it is silent as the ball rotates through the ball screw nut. Replacing the standard ball screw at a high speed and replacing it with the location you are using can reduce the rotational speed of the screw shaft, so make the screw shaft diameter thicker in consideration of the critical speed of the screw shaft or use a difficult fixing method for the screw shaft There is no need to adopt it, leading to cost reduction. The ball screw nut has a short length, the outer diameter is also minimized, and the flange is flattened at two places to reduce the core height and is a compact structure. A large rotational force can be obtained with a small thrust, and it is also suitable for actuator etc.Ball screw nut has built-in brush seal with high dust prevention effect.

-As total teeth number of 72 corresponds to ratchet swing angle of 5 degrees.-Compact round head.-As the driving direction is switchable, it can also tighten a left thread by changing the inserting direction of Torque Handle.

High efficiency is obtained because the ball rolls between the screw shaft and the nut, and the driving torque becomes 1/3 or less compared with the conventional sliding screw.Therefore it is easy to change not only the rotary motion to the linear motion but also the linear motion to the rotary motion.Due to the rolling motion by the ball, the starting torque is extremely small, and stick-slip does not occur like sliding motion, so accurate fine feed can be performed.Since there is no backlash and preload is given, axial clearance can be reduced to zero or less by preloading, and high rigidity can be obtained. It has high efficiency and low heat generation, so you can fast-cut. Shaft end, finished product is screw shaft and ball screw nut standardized for space saving standard. The screw shaft standardizes the terminal in conformity with the support unit, and it is made to be a direct connection structure with the motor.Screw shaft, ball screw nut shape is compact design.An appropriate amount of grease is sealed in the ball screw nut. When penetration of foreign matter is considered, it is necessary to completely cover the screw shaft with a dustproof device (bellows etc.).

-As total teeth number is 24 which corresponds to ratchet swing angle of 15 degrees.-Has a good maintainability because the opening is so large to remove foreign objects easily.

- 3 way loading - 14 oz cartridge, filler pump or 400CC bulk- Durable die-cast head for longer service life- High strength spring for consistent priming- Unique filling nipple design with steel ball to prevent backflow- Special plunger lock for safe and convenient filling- Quality steel lever handle with comfortable rubber grip

-As total teeth number is 24 which corresponds to ratchet swing angle of 15 degrees.-Has a good maintainability because the opening is so large to remove foreign objects easily.

10 ton capacity grease filled hydraulic ram with spring loaded plunger. Provides direct non-twisting application of thrust that is more effective and secure than a mechanical thrust screw. Fully threaded body allows for quick and easy height adjustment. With tommy bar. Fits most brands of pullers and ball joint separators including Kennedy, Sykes-Pickavant, Sealey, Draper, Bergen, Clarke etc. Capacity: 10 ton. Length excluding handle: 190mm. Diameter of ram: 38mm. Thread pitch: 16 gauge x 3/8 BSW

Baut L Hitam dari Yoshinobu memiliki ukuran diameter dari 2-12 mm dan cocok untuk industri perbengkelan, otomotif,manufakturing, dl

Baut L Putih Full Drat dari Yoshinobu ini cocok untuk industri perbengkelan, otomotif,manufakturing, dll